Roofing referrals for Seattle & nearby townsCall: (206) 984-7830
(206) 984-7830

Torch-Down Roofing in Redmond, WA

roofingseattle.net

Granules wearing off, seams opening or blisters forming on a modified bitumen roof in Redmond? A local roofer can look.

Cap sheet blistering on your Redmond roof?
Call now to be connected with a local roofing contractor in Redmond.
(206) 984-7830

Torch-down roofing is modified bitumen sheet that a roofer bonds to the roof by heating the underside with a propane torch. It is built in layers, with a cap sheet on top. Call the number on this page to be connected with a local roofing contractor in Redmond.

Roofers unroll modified bitumen roofing on a flat roof with safety equipment staged nearby, torch-down roofing in Redmond, WA

A material built from separate parts

The membrane, the flashings at walls, the metal edge and the drains all matter on a torch-down roof. A leak can come from any of them. The surface may look fine while the weakness hides where the sheet turns up a wall. Ask the roofer to check each one.

Watching after the torch goes out

Heated asphalt and wood can hold heat long after the flame is off. Roofers commonly stay on site and check seams, edges and the spaces below for warmth or smoke before they leave. That patience is part of safe torch work. Many crews also keep water on hand.

Homes from the 1980s often have later flat-roof additions, and a roofer will check the old framing and flashing before putting a torch near anything.

Call now to be connected with a local roofing contractor in Redmond.
(206) 984-7830

Seams are the weak point

Where one sheet overlaps another, the bond must hold through heat, cold and constant dampness. A seam that has lifted or pulled apart leaves a channel for water. A roofer checks every lap and edge by hand and eye. A roofer can often reseal a lifted lap early.

Weighing repair against replacement

A spot repair costs less today but may only delay a larger bill. If the roof is old and failing in many places, replacement is often the better use of money. A roofer can walk through both options candidly. Ask for both prices side by side.

Questions about warranties

Manufacturers offer warranties on materials, and some require specific installation methods. Ask what applies to your roof, what the warranty covers and what could void it. Keep the paperwork with your home records. Keep a copy with your home records, with the date and the roofer's name.

Know this about Redmond roofs

Reroof permits for Redmond addresses go through the City of Redmond permit office. Its published rule: residential work exempt from permit includes light weight roof covering (composition, metal or similar) where installed unit weight is less than 4 pounds per square foot.

Before work begins, look the company up on L&I's Verify a Contractor page. Washington requires construction contractors, roofers included, to be registered.

Most roof trouble in this part of Washington shows up in the wet season, when a small gap in flashing or a lifted shingle has months of rain to work on.

Storm took out power too? Report it to PSE at 888-225-5773, and stay clear of any downed line.

Much of the housing in Redmond dates to the 1980s or earlier, so a tear-off can uncover older layers or board decking that need extra work.

Nearby, the same kind of help is available in Kirkland, Bellevue and Woodinville.

More about Redmond

Calls come in from across Redmond, including around Overlake, Education Hill, Redmond Town Center.

Downtown Redmond sits just north of Lake Sammamish with the Sammamish River along its west edge.

Torch-Down Roofing questions in Redmond

What does a failing torch-down roof look like?
Look for open seams, bare asphalt where granules have worn off, blisters, cracks near walls and water that stays in puddles. Stains on the ceiling below are another sign.
Why do roofers sometimes avoid open-flame work?
Some buildings have hidden gaps, dry framing or tight cavities where heat could cause a fire. In those cases, a roofer may choose cold-applied, self-adhered or heat-welded products instead.
What affects the price of torch-down roofing?
Roof size, layers, deck condition, flashing detail, access and whether the old roof is stripped all matter. Each independent roofer sets his own price. This referral service does not quote prices.
Does torch-down roofing need a permit?
Rules differ by city and county, and some jurisdictions have requirements for reroofing or for the flame work itself. A roofer or the local permit office can tell you what applies.

More roofing services in Redmond

Torch-Down Roofing nearby

Call now to be connected with a local roofing contractor in Redmond.
(206) 984-7830

Last updated:

☎ Call (206) 984-7830