Roofing referrals for Seattle & nearby townsCall: (206) 984-7830
(206) 984-7830

How much does a new roof cost in Seattle?

roofingseattle.net

Published cost guides put a typical whole-roof replacement in Seattle at roughly $8,045 to $17,399. Where your quote lands depends on roof size, material, pitch, the condition of the deck and how much cleanup the job involves.

Need roofing help now?
Call now to be connected with a local roofing contractor in Seattle.
(206) 984-7830

Published cost guides put a typical whole-roof replacement in Seattle at roughly $8,045 to $17,399. Where your quote lands depends on roof size, material, pitch, the condition of the deck and how much cleanup the job involves.

Quick cost estimator

Typical ranges from the sources cited below, not a quote. The company you hire will price the actual job.

The short answer

One Seattle cost guide, from Angi, gives a typical whole-roof replacement range of $8,045 to $17,399 per job. That is a wide spread because "a roof" can mean a small bungalow with a simple gable or a large house with dormers, valleys and a steep pitch. A statewide figure from This Old House runs wider still, $6,156 to $20,811 across Washington, and it lumps together very different housing markets. Treat every published range as a starting point for budgeting, not a quote. Roofing Seattle is a free referral service, so we do not set prices or sell roofs. A local roofing contractor writes the actual bid after looking at your house.

Use the calculator on this page to line up the numbers you are likely to meet. It uses only the ranges cited at the bottom, and it labels which ones are Seattle figures and which are national.

Cost by material

Material is the biggest lever you control. Seattle-specific per-square-foot figures from the same Angi guide look like this:

MaterialInstalled, per sq ftSource scope
Asphalt shingle$3 to $11Seattle cost guide
Wood shingle$6 to $18Seattle cost guide
Metal$5 to $22Seattle cost guide
Standing seam metal$7 to $30Seattle metal guide

A second source, RoofingCalc, prices the greater Seattle market at $6.50 to $10.50 per square foot for asphalt shingle, $12.50 to $20.50 for metal and $12.50 to $18.50 for cedar shakes. The two sources disagree at the edges, which is normal. Their methods differ, and so do the roofs they describe. If you are weighing materials for a wet climate, our guide to shingles, metal or cedar for the Northwest covers the trade-offs beyond price, and the pages on asphalt shingle roofing and metal roofing explain what each job involves.

What else lands on the bid

The per-square-foot numbers above are for the new roofing itself. Several line items sit on top of that, and Angi's Seattle guide prices two of them separately: removal and disposal of the old roof at $1 to $5 per square foot, and sheathing repair or replacement at $2 to $7 per square foot when the deck turns out to be damaged. You will not know the sheathing number until the old roofing is off. Seattle's wet season makes rotted decking more likely around valleys, skylights and chimneys, so ask every bidder how they price extra decking if they find it, and whether they will call you before doing the work.

Other items to look for in a written bid are underlayment, flashing, drip edge, ventilation, ridge caps, and cleanup with a magnet sweep for nails. A bid that lumps everything into one number makes comparison harder. Ask for the scope in writing.

Why Seattle roofs vary so much in price

  • Size and pitch. Roofing is priced per square foot of roof surface, not floor area. Steep pitches slow the crew and call for more safety setup, since Washington's fall protection rules require systems on roofs steeper than 4 in 12 where there is a fall hazard of four feet or more.
  • Tear-off versus recover. Seattle's residential code says roof replacement includes removing existing coverings down to the deck, and it bars re-covering a roof that already has two or more applications or that is water-soaked or deteriorated. Old craftsman homes with several layers cost more to strip.
  • Tree cover. Houses under firs and cedars collect needles and moisture, which can mean more flashing and deck work, and tighter access.
  • Complexity. Dormers, skylights, chimneys, and valleys add flashing details and labor.
  • Ventilation. Fixing a poorly vented attic is worth doing during a reroof. A roof vent installation runs about $200 to $700 in one national guide. See the guide on attic condensation and roof ventilation.

Permits and energy code

The City of Seattle's SDCI page says a re-roof permit is required when you are repairing an area greater than 500 square feet, and that replacing roof cover, sheathing or insulation on commercial and multifamily projects needs a permit. Re-roof work on one- and two-family homes and townhouses generally does not need one if the building envelope is unchanged apart from adding or replacing insulation. SDCI also says insulation must be added to meet current energy code where existing sheathing or insulation is exposed or roof cavities are uninsulated. Rules outside the city differ by jurisdiction, so see whether you need a permit to reroof near Seattle and ask your contractor who is pulling any permit. Bellevue's guidance, for example, adds that insulation must go to full depth in an exposed cavity on a residential roof replacement.

Repair now or replace later?

Replacement is the most expensive roofing decision most owners make, so it is worth confirming you need it. A basic to comprehensive roof inspection runs roughly $150 to $400 in one national guide, and a small leak repair is $150 to $1,000 in another. If your roof is near the end of its life, repairs only delay the bill. If the damage is local, a repair may buy years. Our guide on when a roof is worth fixing walks through the signs, and you can read about roof inspection and roof replacement in Seattle on the service pages.

How to compare bids

  1. Get at least three written bids with scope, materials, and brand names for the shingles or panels.
  2. Check each contractor on L&I's Verify a Contractor tool before you sign. It shows active registration, the workers' comp account, citations, infractions and lawsuits against the surety bond. Our guide on hiring a roofer in Washington goes through it step by step.
  3. Ask about tear-off versus overlay, underlayment, flashing, ventilation and who handles cleanup.
  4. Ask who pulls the permit, if one is required.
  5. Ask what manufacturer warranties apply to the materials. A contractor's own promises should be in the written bid, not spoken.
  6. Before final payment, get signed lien releases. L&I advises owners to get them from major contractors, subcontractors and suppliers, because unpaid parties can lien the property and an owner could end up paying twice for the same work.

Do not pick the lowest number without understanding why it is low. Missing flashing, thin underlayment or skipped ventilation can all hide in a bid that looks like a bargain.

Insurance, HOAs and timing

If a covered event such as storm or tree damage is why you need a new roof, talk to your insurer before work starts. Washington's Insurance Commissioner says homeowners have the right to select their own contractor, and our page on roof damage and insurance claims covers the process. If you live in a condo or HOA community, the board may control materials, colors and timing, so read who decides and who pays for HOA and condo roofs first.

On timing, Seattle's rainy season runs October through March according to NWS, with more than 75 percent of annual precipitation falling in that stretch. Many owners schedule replacements in the drier months, which can make busy roofers harder to book, so start gathering bids early. A roof that is leaking now should not wait; a tarp and a repair may carry it until you can schedule the full job. See emergency roof repair if you need help sooner.

Budgeting for the unknowns

Because deck condition cannot be confirmed until the old roofing is stripped, many owners set aside a cushion beyond the bid. Using Angi's Seattle figures, sheathing work at $2 to $7 per square foot adds up quickly on a large roof, so ask each bidder whether the number you were given includes any decking and how extra boards would be priced and approved. Also ask how the crew protects landscaping, and whether gutters and downspouts are part of the job or a separate line.

Ready to talk to a roofer?

Call now to be connected with a local roofing contractor in Seattle.
(206) 984-7830

Describe your roof, say whether you want a bid for replacement, and ask any contractor you speak with the questions above. If you have a smaller problem, a roof repair bid is a fair way to compare. You can also browse the full list of roofing services.

Frequently asked questions

How much does a new roof cost in Seattle?
One Seattle cost guide gives a typical whole-roof replacement range of $8,045 to $17,399. Statewide, This Old House gives $6,156 to $20,811. Your own bid depends on size, material, pitch and deck condition.
Is metal roofing much more expensive than asphalt shingles?
In Seattle figures from Angi, installed asphalt shingle runs $3 to $11 per square foot and metal runs $5 to $22. A typical total metal roof installation is quoted at $8,207 to $23,075 in the metal guide.
Does Seattle require a permit to replace a roof?
Seattle's SDCI says a re-roof permit is required when repairing an area greater than 500 square feet. Re-roof work on one- and two-family homes and townhouses generally does not need a permit if the envelope is unchanged apart from insulation. Ask SDCI or your contractor about your specific house.
What should I ask before hiring a roofer?
Check registration on L&I's Verify a Contractor tool, get written bids with scope and materials, ask about tear-off, underlayment, flashing, ventilation and cleanup, ask who pulls the permit, and get lien releases before final payment.
Call now to be connected with a local roofing contractor in Seattle.
(206) 984-7830

Last updated:

☎ Call (206) 984-7830